Kti-networks KCD-302 Series Instrukcja Użytkownika

-1-INDUSTRIALTri-segment Media ConverterKCD-302 SeriesInstallation GuideDOC.060301-KCD-302

-10-Configuration Setting Switches (SW)NO. FUNCTION SETTINGSSW1 TP Port mode OFF Auto-negotiation (default)ON Forced modeSW2 TP Port Duplex OFF Full d

-11-DC Power InputInterface Screw-type terminal block(2 sets for power wire cascading)DC Jack ( -D 6.3mm / + D 2.0mm)Operating Input Voltages +7V ~ +3

-12-CertificateFCC Part 15 Class BCE/EMC EMI EN50081-1 Class BEMS EN55024CE/LVD Safety EN 60950EN 50081-1/1992 :EN55022:1994/A1:1995/A2:1997 CISPR Cla

-13-1.3 Model SpecificationsThe media converter series provides the following fiber options:KCD-302-xxx WaveL. Reference OperatingModel Ext. FX Connec

-14-1.4 Special FunctionsAuto MDI/MDI-X FunctionThis function allows the TP port to auto-detect the twisted-pair signalsand adapts itself to form a va

-15-2. Installation2.1 UnpackingCheck that the following components have been included:• Information CD• The product unit• DIN-rail mounting bracketIf

-16-2.2 DIN-Rail MountingIn the product package, a DIN-rail bracket is provided for mounting theconverter in a industrial DIN-rail enclosure.The steps

-17-2. Unscrew and loose the mounting clamp plate of the bracket. Mountthe bracket with the device onto the DIN rail.5. Screw the clamp with the brack

-18-Make sure that there are proper heat dissipation from and adequate ven-tilation around the device.The final mechanical dimensions after installing

-19-2.3 Mounting on a Panel SurfaceAn optional mounting bracket, as shown below is also available for mount-ing the device on a panel surface such as

-2-(C) 2005 KTI Networks Inc. All rights reserved. No part of this documen-tation may be reproduced in any form or by any means or used to makeany dir

-20-2. Mount and screw the device on the target surface. The final dimen-sion after bracket installation is also shown below:Make sure that there are

-21-2.4 Applying PowerThe product provide two types of power interfaces, terminal block and DCpower jack for receiving DC power input from external po

-22-DC2 + and DC2 - can be installed with another power-pair for delivering themain power input to next converter in a cascading way.Note: Only up to

-23-2.5 Making TP Port ConnectionTP port is featured to support connection to :• Auto-negotiation devices• Auto-negotiation incapable 10BASE-T devices

-24-2.6 Making FX Port ConnectionsFX1 port and FX2 port operate on 100Mbps and full duplex (factorydefault).A variety of fiber options is provided as

-25-3 Configuration Switches & LED IndicatorsThe following figure shows the locations of the configuration switchesand LED indicators:Refer to the

-26-3.1 Configuration SwitchesSW FUNCTION SETTING & STATESW1 TP Port mode OFF Auto-negotiation (default)ON Forced modeSW2 TP Port Duplex OFF Full

-27-3.1.3 FX Port Duplex Settings SW5 SW6This settings are used to set the duplex mode of the FX1 port and FX2port individually. It is recommended to

-28-3.2 LED IndicatorsLED DISPLAY STATUS & INTERPRETATIONPWR Power status ON Power onOFF Power offTPLINK TP port link status ON Link up and no tra

-3-The information contained in this document is subject to change withoutprior notice. Copyright (C) All Rights Reserved.TRADEMARKSEthernet is a regi

-4-Table of Contents1. Introduction...51.1 Features ...

-5-1. IntroductionThe industrial tri-segment media converter series provides one 10/100BASE-TX Fast Ethernet port and two 100BASE-FX ports. It support

-6-For industrial environment, the converters are designed with the follow-ing enhanced features exceeding that of commercial media converters: High

-7-1.1 Features• Support network data transfer at full wire speed• The TP port supports 10Mbps and 100Mbps connections• Auto MDI/MDI-X detection funct

-8-1.2 SpecificationsThis figure shows the important components of the converter:

-9-Twisted-Pair Interface (TP Port, or called copper Port)Connector Shielded RJ-45Pin Assignments Auto MDI/MDI-X detectionSignal Compliance IEEE 802.3