KTI Networks Switch KGD-600 Instrukcja Użytkownika

-1-KGD-600Industrial Web Smart 6-Port GigabitEthernet Switch with Fiber ConnectivityInstallation GuideDOC.070402

-10-Port control Port configuration control via software managementPort Mirroring Mirror received frames to a sniffer portSoftware Management Function

-11-2. Installation2.1 UnpackingThe product package contains:• The switch unit• One product CD-ROM2.2 Safety CautionsTo reduce the risk of bodily i

-12-2.4 Din-Rail MountingThe steps to mount the switch on a Din-rail are:One Din-rail mounting bracket is provided in the product package as shown bel

-13-2.5 Panel MountingOne panel mounting bracket is provided in the product package as shown below:Install the bracket on the bottom of the switch uni

-14-2.6 Applying PowerThe switch provides two types of power interfaces, terminal block and DC power jack for receiving DCpower input from external po

-15-Using DC Power JackWhen an external power system is not available, the switch provides a DC jack to receive power fromtypical AC-DC power adapter

-16-2.8 Making UTP ConnectionsThe 10/100/1000 copper ports support the following connection types and distances:Network Cables10BASE-T: 2-pair UTP Ca

-17-2.9 Making Fiber ConnectionThe mini-GBIC (SFP) port must be installed with an SFP fiber transceiver for making fiber connec-tion. Your switch may

-18-2.10 LED IndicationLED Function State InterpretationPOWER Power status ON The power is supplied to the switch.OFF The power is not supplied to th

-19-3. Advanced FunctionsTo help a better understanding about the software management interfaces, this chapter describes someadvanced functions provid

-2-(C) 2006 KTI Networks Inc. All rights reserved. No part of this documentation may be reproduced inany form or by any means or used to make any dire

-20-3.2 QoS FunctionThe switch provides a powerful Quality of Service (QoS) function to guide the packet forwarding infour priority classes. The versa

-21-3.2.1 Packet Priority ClassificationEach received packet is examined and classified into one of four priority classes, Class 3, Class 2,Class 1 an

-22-3.3 VLAN FunctionThe switch supports port-based VLAN, 802.1Q Tag VLAN and eight VLAN groups.3.3.1 VLAN OperationThe following figure illustrates t

-23-3.3.2.3 Drop Untag Per Port SettingEnable - All untagged packets and priority-tagged packets are dropped. A priority-tagged packetis treated as a

-24-3.3.5 VLAN Group Table ConfigurationThe switch provides a table of eight VLAN groups to support up to eight VLANs at the same time.Each VLAN group

-25-3.3.8 Egress Tagging RulesEgress Tagging rules are used to make change to the packet before it is stored into egress queue of anegress port. Three

-26-3.4 802.1X Authentication Port Access ControlFor some IEEE 802 LAN environments, it is desirable to restrict access to the services offered by the

-27-4. Web ManagementThe switch features an http server which can serve the management requests coming from any webbrowser software over TCP/IP networ

-28-4.3 Main Management MenuThe following information describes the basic functions of the main menu.ConfigurationSystem Switch information, system an

-29-4.4 SystemConfiguration DescriptionMAC Address The MAC address factory configured for the switchIt can not be changed in any cases.S/W Version The

-3-The information contained in this document is subject to change without prior notice. Copyright (C). AllRights Reserved.TRADEMARKSEthernet is a reg

-30-4.4.1 Management VLANManagement VLAN settings allow administrator to access the switch and perform the switch manage-ment over a dedicated VLAN.Th

-31-4.5 PortsConfiguration FunctionPort The port numberLink Port link statusSpeed and duplex status with green background - port is link onDown with r

-32-4.6 VLANsVLAN Configuration DescriptionVLAN Disable Select to disable VLAN functionAll ports are allowed to communicate with each others freely wi

-33-4.6.1 Port-based VLAN ModeConfiguration DescriptionGroup 1, 2 Port-based VLAN group numberMember ports Select member ports for the group[Apply] Cl

-34-4.6.2 Port-based VLAN ISP ModeConfiguration DescriptionJoint port Select a port as the joint port for all 5 port-based VLAN groups[Apply] Click to

-35-4.6.3 Advanced VLAN ModeConfiguration DescriptionIngress Default Tag Click to configure per port Ingress Default Tag settingsIngress Settings Clic

-36-4.6.3.1 Ingress Default TagConfiguration DescriptionPort Port numberPVID Port VID, VID for Ingress Default Tag1 ~ 4095 - decimal 12-bit VID valueC

-37-4.6.3.2 Ingress SettingsConfiguration DescriptionPort Port numberTag Aware Check tag data for every received packetTag-aware - set to activate Tag

-38-4.6.3.3 Egress SettingsConfiguration DescriptionPort Port numberInsert Tag Activate tagging (Insert a tag to the packet)Enable - set to activate t

-39-4.6.3.4 VLAN GroupsConfiguration DescriptionGroup Group numberVID VID of the VLAN to which this group is associated1 ~ 4095 - decimal 12-bit VID v

-4-Table of Contents1. Introduction... 61.1 Features

-40-4.6.4 Important Notes for VLAN ConfigurationSome considerations should be checked in configuring VLAN settings:1. Switch VLAN Mode selectionIt is

-41-4.7 Quality of ServiceQoS Configuration DescriptionPort Port number802.1p 802.1p priority classificationEnable - set to enable this classification

-42-4.7.1 802.1p MappingConfiguration DescriptionPort n Port number ntag m 3-bit User priority tag value m ( range : 0 ~ 7 )Priority class Mapped prio

-43-4.7.2 DSCP MappingConfiguration DescriptionDSCP [0-63] Seven user-defined DSCP values which are configured with a priority class0 ~ 63 - 6-bit DSC

-44-4.7.3 QoS Service PolicyConfiguration DescriptionPort Port numberPolicy Service policy for egress priority among four egress class queuesStrict pr

-45-4.8 Port MirroringConfiguration DescriptionSniffer Port The port is forwarded all packets received on the mirrored portsMirrored Ports Select the

-46-4.9 802.1X ConfigurationConfiguration DescriptionMode Disabled - disable 802.1x functionEnabled - enable 802.1x functionRADIUS IP IP address of th

-47-[Re-authenticate] Click to perform a manual authentication for the port[Force Reinitialize] Click to perform an 802.1x initialization for the port

-48-4.10 StatisticsConfiguration DescriptionPort Port numberTx Bytes Total of bytes transmitted on the portTx Frames Total of packet frames transmitte

-49-4.11 Reboot SystemThis menu is used to reboot the switch unit remotely with current configuration. Starting this menu willmake your current http c

-5-4. Web Management ... 274.1 Start Browser Software and Making C

-50-4.13.2 Upload Configuration FileEnter the path and file name of a configuration file for uploading.Configuration DescriptionFilename Path and file

-51-Appendix. Factory Default SettingsSystem ConfigurationManagement VLAN - VID 0Management VLAN - CFI 0Management VLAN - User priority 0IP Address 19

-52-VLAN Group 1 - VID 1VLAN Group 1 - Member Ports Port 1, 2, 3, 4, 5, 6VLAN Group 1 - Source Port Check DisableVLAN Group 2 - VID 2VLAN Group 2 - Me

-53-Port 1~Port 6 - tag 5 Class 2Port 1~Port 6 - tag 6 Class 3Port 1~Port 6 - tag 7 Class 3QoS DSCP MappingDSCP 1 / Priority 0, Class 0DSCP 2 / Priori

-6-1. IntroductionThe KGD-600 is a managed 6-port Gigabit Ethernet switch which is featured with five copper ports,one mini-GBIC (SFP) port and the f

-7-Industrial FeaturesFor industrial environment, the devices are designed with the following enhanced features exceedingthat of commercial Ethernet s

-8-1.2 Product PanelsThe following figure illustrates the faces of the switch:

-9-1.3 LED IndicatorsLED FunctionPOWER Power statusLNK/1000M/ACT Network port 1000M link status (Port 1 - Port 5)LNK/100M/ACT Network port 100M link